Перейти к основному содержимому

Nominator Pool

Running the Validator in Nominator Pool Mode

  1. Set up the hardware for the validator - you will need 8 vCPUs, 64GB memory, 1TB SSD, a fixed IP address, and 1Gb/s internet speed.

    For maintaining network stability, it's recommended to distribute validator nodes in different geographical locations worldwide rather than concentrating them in a single data center. You can use this site to assess the load of various locations. The map indicates high data center utilization in Europe, especially in Finland, Germany, and Paris. Therefore, using providers such as Hetzner and OVH is not recommended.

    Ensure your hardware matches or exceeds the specifications above. Running the validator on insufficient hardware negatively impacts the network and could result in penalties.

    Note that as of May 2021, Hetzner has prohibited mining on its servers, and this ban includes both PoW and PoS algorithms. Even installing a regular node may be considered a violation of their terms of service.

    Recommended providers include: Amazon, DigitalOcean, Linode, Alibaba Cloud, Latitude.

  2. Install and synchronize mytonctrl as described in the guide here.

    You can also refer to this Video Instruction for additional help.

  3. Transfer 1 TON to the validator wallet address shown in the wl list.

  4. Use the aw command to activate your validator wallet.

  5. Activate pool mode:

    enable_mode nominator-pool 
    set stake null
  6. Create two pools (for even and odd validation rounds):

    new_pool p1 0 1 1000 300000
    new_pool p2 0 1 1001 300000

    where:

    • p1 is the pool name;
    • 0 % is the validator's reward share (e.g., use 40 for 40%);
    • 1 is the maximum number of nominators in the pool (should be <= 40);
    • 1000 TON is the minimum validator stake (should be >= 1K TON);
    • 300000 TON is the minimum nominator stake (should be >= 10K TON);

    (!) Pool configurations do not have to be identical, you can add 1 to the minimum stake of one pool to make them different.

    (!) Use https://tonmon.xyz/ to determine the current minimum validator stake.

  7. Type pools_list to display pool addresses:

    pools_list
    Name Status Balance Address
    p1 empty 0 0f98YhXA9wnr0d5XRXT-I2yH54nyQzn0tuAYC4FunT780qIT
    p2 empty 0 0f9qtmnzs2-PumMisKDmv6KNjNfOMDQG70mQdp-BcAhnV5jL
  8. Send 1 TON to each pool and activate the pools:

    mg validator_wallet_001 0f98YhXA9wnr0d5XRXT-I2yH54nyQzn0tuAYC4FunT780qIT 1
    mg validator_wallet_001 0f9qtmnzs2-PumMisKDmv6KNjNfOMDQG70mQdp-BcAhnV5jL 1
    activate_pool p1
    activate_pool p2
  9. Type pools_list to display pools:

    pools_list
    Name Status Balance Address
    p1 active 0.731199733 kf98YhXA9wnr0d5XRXT-I2yH54nyQzn0tuAYC4FunT780v_W
    p2 active 0.731199806 kf9qtmnzs2-PumMisKDmv6KNjNfOMDQG70mQdp-BcAhnV8UO
  10. Open each pool via the link "https://tonscan.org/nominator/<address_of_pool>" and verify pool configurations.

  11. Proceed with the validator deposit to each pool:

    deposit_to_pool validator_wallet_001 <address_of_pool_1> 1005
    deposit_to_pool validator_wallet_001 <address_of_pool_2> 1005

    In these commands, 1005 TON is the deposit amount. Be aware that 1 TON will be deducted by the pool for processing the deposit.

  12. Proceed with the nominator deposit to each pool:

    Visit the pool link (from Step 9) and click ADD STAKE. You can also make a deposit using mytonctrl, using the following commands:

    mg nominator_wallet_001 <address_of_pool_1> 300001 -C d
    mg nominator_wallet_001 <address_of_pool_2> 300001 -C d

    (!) The nominator wallet must be initialized in basechain (workchain 0).

    (!) Keep in mind that the validator wallet and nominator wallet must be stored separately! The validator wallet should be stored on the server with the validator node to ensure processing of all system transactions. Meanwhile, the nominator wallet should be stored in your cold cryptocurrency wallet.

    To withdraw a nominator deposit, send a transaction with the comment w to the pool address (attach 1 TON to process the transaction). You can also perform this action using mytonctrl.

  13. Invite nominators to deposit into your pools. The participation in validation will commence automatically.

    (!) Ensure that you have at least 200 TON/month in your validator wallet for operation fees.

Pool Configuration

If you're intending to lend to yourself, use new_pool p1 0 1 1000 300000 (maximum of 1 nominator, 0% validator share).

If you're creating a pool for numerous nominators, you might use something like this: new_pool p1 40 40 10000 10000 (maximum of 40 nominators, 40% validator share, minimum participant stakes of 10K TON).

Transitioning a Regular Validator to Nominator Pool Mode

  1. Input set stake 0 to discontinue election participation.

  2. Await the return of both your stakes from the elector.

  3. Proceed with the steps under "Running the Validator in Nominator Pool Mode" from the 4th step onwards.